DesignJet Plotter Repair - Latest comments

Henric [Visitor] in response to: Blue Screen Error DesignJet T120 T520 Plotter

Henric [Visitor] — Thu, 03 Oct 2019 07:37:43 +0000

This worked like a charm.
Our printer is back to working state after BSOD.

Computer Care [Member] in response to: DesignJet T1100 T1100PS and T610 Error Codes

Computer Care [Member] — Thu, 13 Mar 2014 20:20:23 +0000

m azam
Also try this.
Turn off the Plotter.
Disconnect the power from the wall.
Wait 2 mins.
Remove the Formatter / Hard Drive.
Reconnect the power and turn the plotter on.
It wont boot, It should give you a specific error.

turn the plotter off, disconnect the power from the wall.
Wait 2 mins.
Reinstall the Formatter / Hard Drive.
Reconnect the power
Restart the Plotter.
See what it does.

Your firmware update may have failed.
You may need to get the plotter up just enough so you can retry the firmware update.

Computer Care [Member] in response to: DesignJet T1100 T1100PS and T610 Error Codes

Computer Care [Member] — Thu, 13 Mar 2014 20:15:29 +0000

m azam
Error 8:11 refers the the front panel.
System Error: 08:YZ
Problem
Description:
Problem with the Front Panel.

Try the following:
􀂄 Switch the Power OFF from the back of the Printer and disconnect the
Power cord. Reconnect the power cord and power On the Printer.
􀂄 Check that the Front Panel interface cable is not damaged and is
correctly connected between the Main PCA and the Front Panel.
􀂄 Check that the memory module in the Formatter is installed correctly.
􀂄 Check that the connections between the Formatter, the Formatter and the
Formatter are not damaged and are correctly connected.
􀂄 Check that the Printer has the latest Firmware version. If not, update the
Firmware to the latest version.
􀂄 If the System Error continues, replace the Main PCA ?Ã‹ Page 8-144.
􀂄 If the System Error continues, replace the Formatter ?Ã‹ Page 8-140.
􀂄 If the System Error continues, replace the Front Panel ?Ã‹ Page 8-43.

m azam [Visitor] in response to: DesignJet T1100 T1100PS and T610 Error Codes

m azam [Visitor] — Wed, 12 Mar 2014 20:01:29 +0000

we are facing problem after firmware up date
error 8:11
after restart its not booting
may be due to HDD problem?
and i dont have HDD software
can you help us.

m azam [Visitor] in response to: DesignJet T1100 T1100PS and T610 Error Codes

m azam [Visitor] — Wed, 12 Mar 2014 20:00:56 +0000

we are facing problem after firmware up date
error 8:11
after restart its not booting
may be due to HDD problem?
and i dont have HDD software
can you help us.

Computer Care [Member] in response to: DesignJet T1100 T1100PS and T610 Error Codes

Computer Care [Member] — Thu, 26 Jan 2012 18:24:18 +0000

My first thought would be to check the Media Lever Position Sensor
Q5669-60706 DesignJet Media Lever Position Sensor aka Pinchwheel lifter sensor

You can check it's function with an OHM meter.
The sensor can be found on page 7-14 in the service and repair manual.

david mercurio [Visitor] in response to: DesignJet T1100 T1100PS and T610 Error Codes

david mercurio [Visitor] — Thu, 26 Jan 2012 00:38:29 +0000

Lower lever sensor error at paper load: paper loads and then displays "lift media lever" in order to reposition paper edge. Upon lifting lever (printer senses lever lifted), printer displays "lower media lever" but does not detect lever lowered. Message will not go away.
Entering service mode to test sensors (with paper unloaded) printer displays error 54:10 and 07:10.
I am opting first to replace media sensor.
Any suggestions?

Printing Freak [Visitor] in response to: Designjet 500 / 510 / 800 double or offset printing issues

Printing Freak [Visitor] — Thu, 15 Dec 2011 03:22:04 +0000

Very important as we found out. Check the entire length of the carriage belt. It may look good, but can sometimes be a little stretched. They're cheap. Just replace it if you are unsure.